1. Hameg Hm 2008 Manual Pdf
2. Hameg Hm 2008 Manual Online

HM400E/150812 C&E Subject to change without notice © HAMEG Instruments GmbH® DQS-certified in accordance with DIN EN ISO 9001:2008, Reg.-No.: 071040. 6 D-63533 Mainhausen Tel +49 (0) 6182 8000 Fax +49 (0) 6182 800100 www.hameg.com info@hameg.com.

Download HAMEG HM OSCILLOSCOPE UM service manual & repair info for electronics experts. Find great deals for HAMEG HM Oszilloskop 20mhz digital Storage. Shop with confidence on eBay!. I have been experiencing a problem with my Hameg HM oscilloscope. It was working correctly then the trace suddenly went back to the left.

Otherwise the full resolution in the horizontal direction is not obtained. Each signal display obtained with pre-triggering can be “fro- zen” with the corresponding HOLD button. Safety Class I with safety earth conductor; not in safety class II. The current time sweep is inter- rupted.

HAMEG HM Oszilloskop 20mhz digital Storage eBay

Hameg Hm 2008 Manual Pdf

The square-wave edges are now visible on the screen. The maximum operating altitude is up to m non- operating m. In return, however, the read out, visible image appears immediately after the single sweep ends.

The nature of digital storage offers still many more display possibilities, which are fully taken advantage of in the HM Have one to sell?

When the memory mode is switched on, the analog timebase is switched off. Feb 26, Threshold, internal 5mm, external 50 mV.

Symmetrical signal display on the screen without clip- ping on one side necessitates correct X position adjust- ment with the X-POS. Insert probe in 0. An lEC-Bus option is available talk only to transmit stored waveforms to a listener or controller.

The same also applies for replacing the rear cover. In the LF position low frequency frequencies above 1 kHz in the internal and external trigger signal are increasingly attenuated, high frequency disturbances and noise are therefore suppressed.

All buttons in the Y section in out hamrg. Transport damages are not covered by the guarantee. Size of the signal voltage In general, AC voltage values normally refer to the rms value root means square value.

Two signals can be displayed together in this button position alternate mode. Accurate evaluation of such signals is only possi- ble up to approximately 2 MHz repetition frequency. Only 8 cm can be evaluated in the screen graticule on both directions.

HAMEG HM208 Oszilloskop 20mhz digital Storage

This also applies – within certain limits – to whole number multiples or fractions of the line frequency. The scanning, storage and read out process can be repeated immediately by renewed depressing of the RESET button. The following must be noted here: If the second signal is to be plot- ted about the same X axis abscissathe plotting film must be wound back to the starting point of the first signal.

Influence on the leading edge T5: If there is transport damage, the supplier must be informed immediately.

Hameg HM 2 Kanal Storage eBay

They are a hazard to life. For example, at approx. Handling of the CRT needs utmost caution. Otherwise a capacitor of adequate capacitance must be connected to the input of the vertical amplifier with DC coupling. Trace Rotation – used to correct trace angle versus raster. It is important that the sequence of firstly 1 kHz and then 1 MHz compensation must be followed but need not be repeated, also calibrator frequencies of 1 kHz and 1 MHz cannot 028 used for time calibration.

It provides greater picture intensity for certain signals. Select either 1 kHz or 1 MHz output fre- quency. To obtain a well-triggered display in this case, the assistance of the variable time control may be required. Digital Storage Hameb x8bit. It is replaced by the digitally generated quartz control timebase. In this way transient distortions such as overshooting, rounding off, ringing, holes or humps in the pulse top in the vicinity of the leading edge are kept to a minimum. Component-Tester HZ65 Indispensable for trouble-shooting in electronic circuits.

Naturally the sequ- ence can also be reversed. The HZ65 oper- ates with all scopes, which can be switched to X-Y operation ext.

An incorrect sequence when reading out from the memories has the effect in the display of Channel I that only half the information dot density is reproduced.

The HM has a plotter output for connecting a XY plotter. These possess resonance correction elements R-trimmers in combination with coils and capacitors with which it is possible for the first time to simply adjust the probe in the upper frequency range of the vertical amplifier. Postage cost can’t be calculated. Further pressure releases the button and switches back to real time mode. Under certain conditions, 50 Hz or 60 Hz hum voltages can occur in the measuring circuit due to the interconnection with other mains powered equipment or instruments.

Hameg Hm 2008 Manual Online

Horizontal resolution in timebase mode Channel I alone: The internal diameter of the sockets is 4. If this is not done, serious signal distortion may result from spurious cur- rents through the ground leads or chassis parts. However, the visible signal on the screen can be expanded by pressing the X-MAG.

In addition, 20 knob can be used to terminate the plotter writing pro- cess before the complete memory contents are written. But 2 shielded cables with an extra wire forZ can also be used.